Monopole 3D Printed Coronal Cock Ring With Steel Balls
I have designed a 3D printable Monopole Conductive Rubber Coronal Cock Ring Electrode. The design is finished and is available for download on my Gdrive, so if you have access to a 3D printer so that you can make one yourself.
This Electrode is printed in my trademark YELLOW PLA. This insulator comes with 12"/30.5cm of 4mm conductive rubber tubing that takes 2mm plugs. This version comes with three stainless steel amplifier balls to apply pressure to your glans and ensure good electrical contact.
This novel design utilises only one length of 4mm conductive rubber, which is secured in place at one end with a pin and then fed through the two 3D-printed components to create the coronal cock ring.
It will be dispatched with 4mm conductive rubber tubing already fitted most of the way through it. You will need to feed the conductive rubber through the final hole to get it ready for use (it fits in the packaging easier without it being fully assembled).
One side of the Conductive Rubber loop has a pin fitted to secure it in place. Your TENS cable plug secures the other end, you can remove this plug to allow two plugs to attach to this electrode from different channels if you are using a Tri-phase set-up to make it the base connector.
To fit it you loosen the loops and place it over the head of the penis, then tighten the horizontal loop before drawing the loose conductive rubber down through the vertical hole then attach your 2mm plug to the conductive rubber.
I have designed a 3D printable Monopole Conductive Rubber Coronal Cock Ring Electrode. The design is finished and is available for download on my Gdrive, so if you have access to a 3D printer so that you can make one yourself.
This Electrode is printed in my trademark YELLOW PLA. This insulator comes with 12"/30.5cm of 4mm conductive rubber tubing that takes 2mm plugs. This version comes with three stainless steel amplifier balls to apply pressure to your glans and ensure good electrical contact.
This novel design utilises only one length of 4mm conductive rubber, which is secured in place at one end with a pin and then fed through the two 3D-printed components to create the coronal cock ring.
It will be dispatched with 4mm conductive rubber tubing already fitted most of the way through it. You will need to feed the conductive rubber through the final hole to get it ready for use (it fits in the packaging easier without it being fully assembled).
One side of the Conductive Rubber loop has a pin fitted to secure it in place. Your TENS cable plug secures the other end, you can remove this plug to allow two plugs to attach to this electrode from different channels if you are using a Tri-phase set-up to make it the base connector.
To fit it you loosen the loops and place it over the head of the penis, then tighten the horizontal loop before drawing the loose conductive rubber down through the vertical hole then attach your 2mm plug to the conductive rubber.
Original: $17.56
-65%$17.56
$6.15Description
I have designed a 3D printable Monopole Conductive Rubber Coronal Cock Ring Electrode. The design is finished and is available for download on my Gdrive, so if you have access to a 3D printer so that you can make one yourself.
This Electrode is printed in my trademark YELLOW PLA. This insulator comes with 12"/30.5cm of 4mm conductive rubber tubing that takes 2mm plugs. This version comes with three stainless steel amplifier balls to apply pressure to your glans and ensure good electrical contact.
This novel design utilises only one length of 4mm conductive rubber, which is secured in place at one end with a pin and then fed through the two 3D-printed components to create the coronal cock ring.
It will be dispatched with 4mm conductive rubber tubing already fitted most of the way through it. You will need to feed the conductive rubber through the final hole to get it ready for use (it fits in the packaging easier without it being fully assembled).
One side of the Conductive Rubber loop has a pin fitted to secure it in place. Your TENS cable plug secures the other end, you can remove this plug to allow two plugs to attach to this electrode from different channels if you are using a Tri-phase set-up to make it the base connector.
To fit it you loosen the loops and place it over the head of the penis, then tighten the horizontal loop before drawing the loose conductive rubber down through the vertical hole then attach your 2mm plug to the conductive rubber.
